MINI ELM327 V1.5 OBD-II CAR DIAGNOSTIC SCANNER

Mini ELM327 v1.5 OBD-II Car Diagnostic Scanner for iOS or Android

Features:
* Fully compatible with ELM327 V1.4b
* All ELM327 supported software are available to use
* Faster than ELM327 four times or higher. (ELM327 is RISC 8bit 44MHz MCU, iCar is ARM 16bit MCU)
* Due to the android diagnostic software becomes heavier to run, suggest to use on smart phone with CPU 800Mhz or higher, 1GHz recommended
* Low standby power consumption sleep mode
* Lower power consumption than ELM327
* LED indicator is in the front side toward user for easier check of linking status.
* Support J1939 protocol more than ELM327
* WiFi 802.11 b/g or 802.11n module

Specification:
* OBDII decode chip: ARM 16bit MCU
* Firmware: ELM327 Version 1.4b compatible
* Transfer baud rate: 4800 / 9600 / 10400 / 38400 (default) / 115200 / 500K
* Input interface: OBDII male 16pin
* Output interface: 802.11n
* LED Indicator: Power(red) / OBD(green) / Link(blue) (PC or smart phone)
* Operating Voltage: 12V from car OBD2 socket, including over voltage /shortage protection
* Nominal Idle current: 45mA
* Net Weight: 31g / Gross Weight: 60g
* Communication range: 500m open field
* SSID: VGATE (discontinued) or BUYOBD (current)
* Encryption: Open (VGATE) and WEP shared/WEP128 (BUYOBD)

Usage:
1. Keep car key at off position
2. Plug the Vgate scantool into Car OBDII female socket.
OBD2 socket is usually below the driving wheel.
The Vgate should blink all 3 LEDs and off again.
Only red power LED remains on.
3. Insert car key.
4. Switch car key to Accessory ON position,
5. Turn on WiFi of PCtebook/smart phone.
Check Windows control panel>wireless network>Setting>Advanced>Wireless mode>IEEE 802.11b/g/n.
Check android wifi setting, turn off existing link.
Check iPhone Wi-Fi networks, turn off existing link.
6. Scan the Vgate wifi device from your Desktop/Notebook PC/PDA/phone.
Find SSID "VGATE" or "BUYOBD".
The Vgate blue LED should be on now. Otherwise, the device doesnt respond to the scanning.
7. For Windows/Android,
If SSID is "VGATE", it is DHCP mode, not need to set up.

If SSID is "BUYOBD", enter 13 digits password shown on the label of the white plastic case.
IP: select "Fixed", and enter "192.168.0.10"
Subnet mask: enter "255.255.255.0"
DNS: keep blank

For iPhone/iPad:
If SSID is "VGATE", it is DHCP mode, not need to set up.

If SSID is "BUYOBD", enter 13 digits password shown on the label of the white plastic case.
IP: change from "DHCP" to "Fixed"!
IP: enter "192.168.0.11" or later
Subnet mask: enter "255.255.255.0"
HTTP local port: enter "35000"
8. App setup: select Vgate device as KiWi wifi or ELM327.
Click link, app will build a link to Vgate.
App may take time for scaning vehicle protocol less than a minute or so.
App starts to show static data once recognize the protocol and has correct table of associated sensor.
The Vgate green LED should be blinking now.
The faster data rate the protocol is, the the faster the green LED blinks.
Turn off the app, not minimize", if app fails to link and doesnt show data. Start another app and try again.
Some vehicles may have to turn car key to "ON/Start" position to activate car ECU.
Turn car key to "ON/Start" position to read real-time data.

Pickup at Ayala the 30th Mall Meralco Ave Ortigas Center[/url] (8am-5pm), or C Raymundo Pasig (by schedule).

https://www.google.com.ph/maps/place/Ayala+Malls+The+30th/@14.5809813,121.0618292,17z/data=!4m5!3m4!1s0x0:0x60548d2f56e0842!8m2!3d14.580566!4d121.064447

Add P200 for LBC shipping, P140 for JRS shipping. Grab Express also available for same-day delivery (amount depends on location - Metro Manila only).